Used in apparel, home textiles & garment accessories.
Dedicated to in-depth expertise and continuous innovation in knitted textiles.
A 160 GSM bamboo viscose jersey can be approved in ten minutes on a lab dip and a three-metre sample. It can also fail six weeks later, when the bulk roll comes back from the first wash noticeably shorter than the sample and the neckline of the finished tee has spiralled to one side. Both outcomes come from the same fiber. The difference is whether the spec sheet was written before the order or after the complaint.
So here is the short answer up front: bamboo viscose fabric is a regenerated cellulose knit with excellent drape, a cool dry hand and strong moisture handling, and it is a fiber that demands discipline on shrinkage, spirality, wet strength and labeling. Buyers who lock those four points down at sampling stage usually get a soft, premium-feeling fabric that sells well in basics, loungewear and trims. Buyers who treat it like cotton often inherit a rework bill.
This guide is written from the production side of a knit mill in Keqiao, where we spin, knit, dye and finish cellulose-based knits for apparel, home textile and accessory programs. It covers what the fiber is, how it behaves, which knit structures suit it, what numbers to put in a purchase specification, how blending changes cost, and what to check before bulk approval.
Bamboo viscose is a softness-and-drape fiber, not a durability fiber. Specify it for hand feel and moisture comfort, then engineer shrinkage, recovery and seam stability into the fabric through construction and finishing rather than expecting the fiber to supply them.
Content
Bamboo viscose starts as bamboo pulp, which is dissolved and regenerated through the viscose process and then spun into filament that is cut into staple and spun into yarn. Chemically the finished fiber is cellulose — the same family as cotton, modal and standard viscose — which is why it dyes with reactive dyes, absorbs moisture the way cellulose does, and behaves like a rayon on a washing label.
That last point matters commercially. There is a second, much smaller category sometimes called bamboo linen, where bamboo stems are crushed and the natural fibers are mechanically extracted. It feels coarser, costs far more and is rarely what a buyer receives when they ask for "bamboo fabric." Almost every soft, fluid bamboo knit on the market is regenerated cellulose. If your supplier cannot tell you which route the fiber came from, the conversation about performance and price will not go well.
Buyers rarely choose bamboo viscose in isolation. They compare it against cotton jersey, against modal and against polyester blends, usually on hand feel, weight and landed cost. The table below sets out the practical differences we see on the knitting floor and in customer wear trials.
| Fiber | Hand and drape | Moisture regain (typical) | Wet strength | Pilling tendency | Cost position |
|---|---|---|---|---|---|
| Bamboo viscose | Very soft, fluid, cool touch, high luster | About 13% | Lower when wet; handle with care in washing | Moderate to high in loose knits | Mid to upper-mid |
| Cotton | Dry, slightly crisp, holds shape well | About 8.5% | Reasonably stable when wet | Low to moderate | Mid, volatile with crop prices |
| Modal / regenerated cellulose | Soft, smooth, slightly more body than viscose | About 12.5% | Better than standard viscose | Low to moderate | Upper-mid |
| Polyester | Dry, resilient, shape-retaining | Below 1% | High | Controlled by fiber type and finishing | Low to mid |
The practical takeaway is that bamboo viscose buys you comfort and appearance, and you pay for it in dimensional stability. That is a design decision, not a defect. A 100% bamboo viscose tee is a different product from a 60/40 bamboo-cotton tee, and the two should never share a single specification document.
Treat bamboo viscose as a cellulose fiber in every technical decision — dye class, washing instruction and care label — and the commercial conversations become much simpler.
Two numbers explain most of what buyers notice about bamboo viscose: its high moisture regain and its low wet modulus. The first gives the cool, dry-feeling surface and quick moisture transport that make the fiber popular in summer knits and sleepwear. The second means the fiber softens and stretches more when wet, which is exactly when a garment is being washed and pulled.
Before looking at construction choices, it helps to see how far bamboo viscose sits from other fibers on moisture absorption, because that single property drives comfort claims, drying time and dyeing behaviour.
The gap between roughly 13% and under 1% is the reason a bamboo viscose jersey feels different against skin from a polyester interlock of the same weight, and why it holds a crease differently after laundering. It also explains why drying behaviour has to be tested rather than assumed: a heavier bamboo terry can still feel damp several hours after a wash, even though the fiber itself absorbs quickly.
For buyers building a comfort story, this is the useful part of the fiber's profile. It supports a factual claim about moisture absorption and breathability in a mid-weight single jersey. It does not support sweeping claims about the fiber being naturally antibacterial or odour-free after repeated washing, because those effects fade with finishing and use, and in many markets such wording needs substantiation.
On the knitting machine, bamboo viscose yarn is smoother and less hairy than cotton, so needle wear is lower and the fabric surface comes off the machine with a clean, slightly lustrous face. The trade-off is that smooth filament-like surfaces in a loose knit can slide and pill. That is a construction problem, solved with tighter stitch density, higher twist yarns or a small percentage of a companion fiber, rather than a fiber problem.
High moisture regain is the fiber's commercial advantage and the root of its stability problems; both need to appear in the same technical discussion with your customer.
Not every knit construction rewards this fiber. The ones that do are those where drape and surface softness are more valuable than body and resilience. In our own range, the cellulose-based constructions most often requested in viscose and bamboo-viscose yarns are single jersey, rib, interlock, terry and air-layer spacer knits.
Single jersey in the 130–180 GSM band is the classic bamboo viscose fabric for t-shirts, sleep tops and camisoles. With 5% elastane it becomes a stretch jersey at 160–200 GSM that recovers well at the neckline and armhole. The construction is thin, so spirality and shrinkage have to be controlled at finishing; open-width compacting plus a controlled tumbling step gets most lots into a 5% length shrinkage target without losing the soft hand.
Lenzing Viscose Stretch Single JerseyA lightweight 32s Lenzing viscose and 30D spandex single jersey with soft sheen and clean recovery, suited to t-shirts and base layers.View Product →
Rib is where bamboo viscose earns its keep as a trim. A 2x2 or 4x2 rib at 200–260 GSM gives cuffs, waistbands and neckbands a soft edge that does not feel tight, and the fiber's luster makes stripe effects read clearly. Because rib stretches in width, the recovery of the yarn matters more than in jersey; a small elastane content is usual, and the finishing route needs to avoid over-stretching the tube.
Lenzing Viscose Striped Rib KnitA 32s Lenzing viscose and 30D spandex rib with raised vertical stripes, offering soft luster, shape recovery, and a slimming look for fitted tops.View Product →
Terry in bamboo viscose or viscose-cotton blends sits at 240–320 GSM and is used for loungewear, beachwear cover-ups, robes and home textiles. Loop density controls how much the fabric pills and how quickly it dries. A tighter, shorter loop reads more premium and survives washing better than a loose, tall loop, even at the same weight.
Rayon Terry Loop Knit FabricA viscose/rayon terry with a soft looped surface and moisture-absorbing hand, adaptable across apparel, home textiles, and personal-care items where comfort matters.View Product →
When a customer wants the softness of cellulose without the drape of jersey, interlock and air-layer spacer structures are the answer. Air-layer knits at 240–320 GSM trap a little still air between two faces, which gives body and a more structured silhouette, and they hide the lightweight feel that some buyers dislike in pure jersey. These structures also reduce spirality because the two faces balance each other.
Heavy, high-recovery structures such as dense fleece and technical spacer fabrics are better served by polyester and poly-cotton blends. Bamboo viscose can be used in a fleece pile, but the pile flattens faster and the fabric loses its loft after repeated washing. For outerwear with abrasion demands, cellulose knits should be a blend component, not the whole story.
Choose the structure first and the fiber second: jersey and rib for softness, terry for texture, air-layer and interlock when the garment needs body, and polyester-blend routes when the garment needs abrasion resistance.
Most disputes on cellulose knits are not about quality in the abstract. They are about a specification that was never written down. A purchase order that says "bamboo jersey, soft hand, good quality" gives a mill nothing to test against and gives a buyer nothing to reject against. The specification below is the one we recommend for apparel programs, and it is close to what we issue on our own bulk orders.
| Parameter | Common commercial tolerance | Why it changes the outcome |
|---|---|---|
| Composition | Declared fiber content within ±3% | Drives labeling, duty classification and care instructions |
| Weight (GSM) | ±5% on the agreed nominal | Affects yield per garment, opacity and cost per piece |
| Usable width | Minus 2 cm / plus 3 cm on open width | Determines marker efficiency and fabric consumption |
| Shrinkage after 3 home washes | Length ≤5%, width ≤4% | The single biggest source of customer returns on viscose knits |
| Spirality / torque | ≤3% on single jersey | Leg and side-seam twist visible after washing |
| Colourfastness to washing | Grade 4, change and staining | Protects the shade claim and the accompanying garments |
| Colourfastness to rubbing | Grade 3–4 dry, 3 wet | Matters on deep shades and on ribbed trims |
| Pilling resistance | Grade 3–4 after 4 hours Martindale | Controls how the surface looks after a month of wear |
| pH value | 4.5–7.5 | Skin comfort and a common failure in third-party testing |
Two of these deserve extra attention. Shrinkage should always be stated with the wash method attached, because a 5% figure measured under one protocol is not the same as a 5% figure measured under another. Spirality should be stated for the garment panel, not the greige roll, since torque often appears only after the first domestic wash.
If your product is going into a market with mandatory testing, ask for the test standard as well as the result. A pilling grade without a method is a number without meaning. If you are still comparing fabrics at an earlier stage, this knitted fabric guide covering structures, GSM and stretch is a useful companion for reading the construction side of a spec.
Every tolerance you leave out of the specification is a tolerance the mill will choose for you, and it will be chosen to protect yield rather than your retail returns rate.
Pure bamboo viscose is beautiful and slightly fragile in the wrong garment. Blending is how most commercial programs balance the hand feel against durability, recovery and price. The blends below appear repeatedly in buyer requests, and each one solves a specific problem.
Cost engineering is where honest mills earn their reputation. Moving from 180 GSM to 160 GSM saves fiber but changes opacity and drape, and on a light shade the difference shows in the fitting room. Substituting part of the viscose with polyester reduces the landed cost and also reduces the moisture story the label is selling. Both are legitimate choices as long as the buyer knows which specification has been changed.
Weight targets deserve the same scrutiny. A 150 GSM bamboo jersey for summer tees and a 260 GSM air-layer for autumn sweatshirts are different products with different finishing routes, not the same fabric at two thicknesses. If the range is built around several weights, specify each one separately, including its own shrinkage target.
Blend for the problem you actually have — recovery, strength, opacity or cost — and write the new blend into the specification rather than letting it appear quietly in the bulk lot.
Keqiao, in Shaoxing, sits next to the China Textile City market and is one of the densest knit fabric clusters in the world. The practical advantage for a buyer is not only choice. It is the ability to move from yarn to greige to dyeing to finishing within a short radius, which shortens the sample loop and makes small corrections cheaper to run.
Our own position in that cluster is as a knit fabric manufacturer covering knitting, processing and raw material supply, with a catalogue built around air-layer knits, ponte roma, interlock, rib, single jersey, piqué, waffle, terry, crepe, fleece and mesh. Cellulose-based constructions sit inside most of those families, which means a bamboo viscose request can usually be matched to an existing construction and adjusted rather than developed from zero.
For buyers used to working with a wholesaler or trading desk, going directly to a knit mill usually shortens communication on construction questions, because the person answering has seen the machine. For buyers who need several unrelated fabric families from one shipment, a mixed container consolidation through a trading partner can still make sense. The decision should follow order complexity, not habit.
Language coverage matters more than most buyers expect. Technical vocabulary around stitch density and finishing is where misunderstandings start, so a supplier able to discuss the specification in your working language reduces the risk of a well-intentioned but wrong sample. Our own team works across English, Chinese, Russian, Spanish, Arabic and Turkish enquiries for this reason.
Choose a supplier on the strength of the questions they ask you, because the mill that queries your wash method and your seam type is the one that will catch the problem before the bulk run.
This is the section buyers forward to their legal team. In the United States, fiber made from bamboo through the viscose process must generally be disclosed as rayon on the label; describing it simply as "bamboo" is not compliant for the fiber content. In the European Union, the accepted fibre name for this material is viscose. Other markets have their own vocabulary, and the label wording should be confirmed per destination before the hangtags are printed.
Composition claims follow the same logic. "Bamboo viscose" is a useful marketing phrase, but a compliant label needs the regulated fiber name plus the percentage. If a garment contains 62% regenerated cellulose from bamboo, 33% cotton and 5% elastane, those figures belong on the label in the wording your market accepts, not in a rounded-up story.
Environmental claims carry the highest risk. The viscose route uses a solvent system that modern mills recover and reuse, which is a genuine improvement, but it is not a closed loop everywhere and it is not accurate to describe the fabric as chemical-free. If your brand wants a sustainability message, base it on verifiable supply-chain documentation for the pulp and on measured performance — durability, wash life, actual fiber content — rather than on adjectives.
Care instructions also belong in this conversation. Bamboo viscose knits perform best with a cool, gentle wash and low-temperature drying. Telling the customer that plainly protects the garment better than any technical improvement in the fabric, and it reduces the returns that come from a hot wash and a tumble dryer.
Finalise the fiber name and the percentage for each destination market before you approve bulk, because a beautiful fabric with a non-compliant label cannot be sold.
Approval should not rest on a hand squeeze and a colour match under office lighting. The checks below are the ones that catch most of the failures we see on cellulose knits, and they can all be run on a few metres of sample.
Keep the approved sample, sealed and dated, with the specification attached. When a dispute arises two months later, that bundle of fabric and paper settles it faster than any email exchange, and it gives both sides a shared reference for the next order.
Wash, measure, stretch and inspect before approving anything, because every one of those four checks costs minutes at sample stage and real money at bulk stage.
In performance terms, largely yes. Both are regenerated cellulose. The difference is the raw material source and the marketing language, and in several markets the required label name for the fiber is rayon or viscose rather than bamboo.
It can, particularly in single jersey that has not been properly compacted. A well-finished knit is usually specified at 5% or less length shrinkage after three home washes, and that figure should be written into the order rather than assumed.
Most summer t-shirts use 130–180 GSM single jersey, with 5% elastane stretch jersey often chosen for a closer fit. Anything above 200 GSM in a plain jersey starts to read as a heavier, structured garment rather than a basic tee.
Treat that claim carefully. Any antimicrobial effect observed in the fiber is not guaranteed to survive dyeing, finishing and repeated laundering, and many markets require substantiation before such wording appears on packaging or in product copy. Moisture absorption is the claim that can be documented.
Loose constructions pill more than tight ones. A grade 3–4 result after four hours of Martindale testing is a realistic target for a good jersey, and tighter stitch density or a small polyester component will improve it further.
Minimums depend on colour count and whether the construction already exists in the mill's range. Multi-colour orders raise the minimum because each shade needs its own dyeing run. Sampling is typically fast; bulk time is dominated by dyeing and finishing, so confirm both dates before committing to a delivery window.
Yes, subject to the usual metamerism caveats. Cellulose dyes behave predictably, but the same shade can read slightly differently on a luster-rich viscose surface than on cotton. Approve the lab dip on the actual substrate and under daylight-equivalent light.
Most bamboo viscose questions come down to one theme: the fiber gives you comfort and appearance, so the specification must supply the stability.
If you are building or replacing a bamboo viscose program, the efficient sequence is short. Decide the garment and the wash method first, then the weight and structure, then the blend, then the tolerances. Send those four elements to two or three knit mills and compare the answers rather than the price list, because the asking price only tells you what is included in the quotation, not what will arrive in the container.
Our team in Keqiao works with buyers on exactly this sequence — matching a construction from our knit range to a target hand feel, running samples against a written specification, and confirming shrinkage, colourfastness and composition before bulk. If you already have a tech pack or a reference swatch, that is enough to start.
Share your target weight, composition, wash method and order quantity, and we will come back with a construction proposal and a realistic timeline.
A bamboo viscose fabric order succeeds when the specification is agreed before the sample is cut, not when the complaint arrives after the first wash.





